Knowing Plumbing Basics is Important When Installing a Bathtub
Knowing Plumbing Basics is Important When Installing a Bathtub
Blog Article
This article down below in relation to Tools You Need to Install a New Bathtub is fairly entertaining. Don't overlook it.
Setting up a bathtub isn't exactly rocket science, but it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately tough task. If the old tub is conveniently available, the task can move easily; if you have to open up a wall to eliminate the old tub and also place the new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need an assistant to leave the old tub as well as embeded in the new one. Make certain you have actually certified on your own for the task as well as fit trying it. Instead of employing a service provider to take control of a halfway-completed task, it is much better to take into consideration utilizing one before you begin. Possibilities are you might need a professional plumber to make tube links.
This post will help you mount a new bathtub in your bathroom if you have actually already acquired a new bathtub as well as don't require to change the arrangement of your previous supply of water pipes.
Your tools and product checklist ought to comprise the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be rather problematic because of the limited access that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this procedure. As soon as the taps have been removed, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Before proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in place between the faucet and also the sink. Safeguard the faucet in place with the producer offered backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous type must be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Tub
Using the two wooden boards under its feet, put the tub in the needed position. The wooden boards are practical in evenly spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four small points.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the level and also adjusting the feet on the bathtub until the level reviews degree.
To mount taps, fit the bottom of the outermost adaptable faucet connector to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
Activate the water as well as examine all joints as well as new pipework for leakages and tighten them if essential. Fill the bath tub and likewise examine the overflow outlet and also the normal outlet for leakages.
Ultimately, repair the bath paneling as described in the producer's instruction manual. Tiling and also sealing around the bath tub ought to wait until the bath tub has actually been used a minimum of once as this will certainly resolve it into its last setting.
Getting ready for the Setup
First of all, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets unit to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to permeate the wall in between the bath and the tiling, bring about issues with wetness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently readily available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that page about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when perusing the internet. Be sure to take a moment to promote this page if you appreciated it. Thanks for taking the time to read it.
Just a call away! Report this page